How to clean the engine bay and the underside

A clean engine bay under an open hood, with hoses and chrome fittings

The parts of a car you rarely look at collect the worst of the road: oily dust under the hood, salt and mud underneath, leaves in the drains. This guide shows how to clean them gently, with low water pressure and the electrics covered, and how to keep the drains and weather seals working.

An engine bay does not need to look new, but a clean one is easier to check, and a fresh drip or a split hose stands out against clean surfaces. Built-up oily grime holds heat and moisture against rubber and metal. Leaves and twigs along the foot of the windshield can block the drains that carry rainwater away.

Underneath, the threat is salt, mud and grit packed into the wheel wells and the fender liners, where they hold moisture against the metal long after the road has dried. Gentle, regular rinsing does more here than a hard blast now and then. Water near electrics needs care, so these jobs are done on a cool engine, with low pressure and a light hand.

Signs it needs attention

  • A layer of oily dust on the plastic covers under the hood
  • Leaves and twigs packed into the tray below the windshield
  • Mud or a white salt crust caked inside the wheel wells
  • Water pooling on a floor mat or in the spare tire well
  • A damp, musty smell after rain with no spill to explain it
  • Weather seals that look cracked, flattened or chalky

Prepare a cool engine bay

Start with the engine cool to the touch, after the car has sat long enough for the hood and the metal under it to lose their heat, since water or cleaner on a hot engine can damage parts and burn you. Pick out loose leaves and debris by hand or with a soft brush. Then read what the owner's manual says about washing the engine bay, because some makers advise against it.

Cover the parts that dislike water: the air intake, the fuse box, the battery terminals, the alternator and any exposed electrical connectors. Plastic bags and tape work, or a towel tucked loosely where a bag will not stay. If the car is a hybrid or electric, leave the orange high-voltage cables and anything marked high voltage alone, and follow the manual.

  • Engine cool to the touch before any water or cleaner
  • Intake, fuse box, battery and connectors covered
  • High-voltage parts left alone on hybrids and electric cars

Clean the engine bay gently

Put gloves on, then mist an engine bay degreaser or a cleaner labeled for engine bays onto the grimy surfaces, working from the bottom up so it does not run in streaks. Let it sit only as long as the label says, and work it with soft brushes of different sizes. Never let it dry onto rubber or plastic.

Rinse with a gentle spray from a hose nozzle on a low setting, never a pressure washer, and keep the water off the covered areas and every connector. Use only as much water as it takes to carry the cleaner away. Remove the covers, blot standing water with towels, and leave the hood open for a while so the rest can dry before you start the engine.

  • Gloves on for the degreaser, label followed
  • A low hose setting, never a pressure washer
  • Covers off and the hood left open to dry

Rinsing underneath and inside the wheel wells

Rinse underneath with the car standing on flat, level ground and the parking brake on, never with the car resting on a jack. A hose with an angled wand or a rolling underbody sprayer reaches under the sills and along the floor without anyone lying beneath the car. Work from the front toward the back so the grime runs out behind you.

The plastic fender liners inside each wheel well trap mud and salt in their ribs and edges. Turn the steering wheel to one side to open up the front wells, scrub them with a mild cleaner on a long-handled brush, then rinse until the water runs clear. Check local rules where the water runs to a storm drain, or do this at a self-serve wash bay.

  • Car on level ground, parking brake on, nobody underneath
  • Front wheels turned to open up the wells
  • Liners rinsed until the water runs clear

Drains, weather seals and keeping it that way

Cars have small drain holes along the bottom of the doors, at the corners of the trunk or hatch, around a sunroof and in the tray under the windshield. When leaves or dirt block them, rain sits inside and can find its way into the cabin. Clear the openings you can see by hand and rinse the windshield tray gently; the owner's manual shows where the others are.

Weather seals around each door, the trunk lid and the windows stay supple longer when they are kept clean. Wipe them with a damp towel and mild soap, and treat dry seals sparingly with a rubber care product whose label names them. Water on the floor after rain, a leak under the hood or a warning light on the dash goes to a mechanic, since cleaning cannot fix any of them.

  • Door, trunk and windshield-tray drains kept clear
  • Seals wiped clean, with rubber care used sparingly
  • Water inside, leaks and warning lights taken to a mechanic

The kit

  • Plastic bags and tapeCover the intake, fuse box and connectors before any water goes on
  • An engine bay degreaserLoosens oily grime so it rinses off with little water and no scrubbing
  • Soft detailing brushes in several sizesReach between hoses and around brackets without scratching
  • A hose nozzle with a gentle settingRinses at low pressure that will not force water into the electrics
  • A wheel well brush on a long handleScrubs the fender liners without anyone crawling under the car
  • A rubber care productCleans and conditions weather seals so they stay soft and pliable

Generic items only; Prime Axle names no products. Read each product's label and follow it.

What to leave out

  • Water or cleaner on a hot engine, which can crack parts and burn you
  • A pressure washer under the hood, which forces water into electrics
  • Spraying straight at connectors or the fuse box, which can short them
  • Degreaser without gloves, or left to dry on rubber and plastic
  • Getting under a car held up only by a jack, which can slip

Questions about engine bay and underside